TE Motorsport by TAG Engineering Group. | ECU Master ADU Change Log

ADU Display Change Log (Incl. Tested Version)

我們一直不斷的進行更完善的功能更新以及問題修復，目的是希望能提供更棒更優異的使用體驗，以下更新記錄包含了先行版(測試版)，對此可能會有部分功能不穩定，如遇到使用上的功能問題，請聯繫客服並嘗試退回之前的版本進行使用。

Service Mail : tech@tag-parts.com

2024-09-03 Client: 105.1-exp Firmware: 105.1-exp

Firmware:

Fixes:
- Fixed incorrect track recognition after resetting current track data via the button when the track was undefined

2024-09-03 Client: 105.0-exp Firmware: 105.0-exp

Firmware:

New features:
- “Button defined track delete” button – Pressing this button deletes the currently button defined track from the device’s memory. After upgrading to FW105.0, the configuration of the “Button Defined Track Delete” button will be copied from the “Button Defined Track Start/Finish Line Set” button. In this case, the function of the “Button Defined Track Start/Finish Line Set” button will remain the same as before (a double-click of this button will cancel track acquisition and delete the previously defined track). However, if the “Button Defined Track Delete” button is configured separately from the “Button Defined Track Start/Finish Line Set” button, pressing the “Button Defined Track Start/Finish Line Set” button and pressing it again to cancel will no longer delete the current track data but will only cancel the new track acquisition
- “Flying start” option to the Hill Climb mode, allowing the use of Hill Climb mode without needing to stop at the start line to define the track and start timing the lap
- Added the option to choose the data source from the IMU, which will be used to calculate the Gforces for the “G-force” indicator and the ‘adu.latG’ and ‘adu.longG’ channels
- Automatic brake bias calculation along with a new channel, ‘adu.brake.bias’ measured in [%]. This feature can be configured in the Client window under ‘Configuration Brake Bias’ →
- Added channels ‘adu.track.predictiveLapTime’ and ‘adu.track.lastLapTime’ measured in [s]
- Support for the new “6×1 Ecumaster” keyboard
- New USA tracks added:
  - Eagles Canyon Raceway
  - Motorsport Ranch Cresson
  - Motorsport Ranch Houston
  - Hallett Motor Racing Circuit
Improvements:
- Shift Light: PIT Limit Indicator: added “None” option for colour selection
- Added an option to change the functionality of the ‘Reset track data’ button. This can be configured in the Client window under ‘Configuration LapTiming Reset track data button → →
function:
- Reset all track data – Pressing the button deletes the best times for all saved tracks (same functionality as before FW 105.0, default setting).
- Reset current track data – Pressing the button deletes the best times only for the track on which the user is currently located.

2024-08-23 Client: 104.1 public release Firmware: 104.1 public release

Client:

Improvements:
- Improved CSV export: Decimal places are now better suited for each exported channel, and a trailing column separator has been added after the last value in each row
Fixes:
- Resolved an issue that caused GPS channels to be inaccurately exported to CSV file
- Fixed loading of the logs saved in ADU software version 104.0 with firmware 92.x
- Fixed an issue that caused user channels to not be saved properly after loading a project file

Firmware:

Fixes:
- The version number of the logs recorded by the USB logger has been updated to V5. As a result, these files can no longer be incorrectly loaded in older client versions.

2024-06-17 Client: 104.0.1-exp Firmware: (no changes)

Client:

Fixes:
- The application now longer crashes when pressing OK button in the Merge Project window

2024-04-19 Client: 104.0-exp Firmware: 104.0-exp

Firmware:

New features:

Added the current page number in the new “adu.page” channel (first page has value “1”).
Added buttons for freezing/unfreezing the adu.distanceMeters. New channels added:
- “adu.distanceMeter.frozen”
- “adu.distanceMeter2.frozen”
Virtual Fuel Tank features:
- The Fuel Tank Size can now be defined by a channel. New channel added:
  - “adu.vft.fuelTankSize”
- Added support for Stage and Road modes. New channels added:
  - “adu.vft.stage.distanceFromLastReset”
  - “adu.vft.stage.usedFuelFromLastReset”
  - “adu.vft.road.distanceFromLastReset”
  - “adu.vft.road.usedFuelFromLastReset”
  - “adu.vft.isStageMode”
- New USA tracks added:
  - Buttonwillow
  - Willow Springs
  - Thunderhill
  - Chuckwalla
  - Thermal blue
  - High Plains
  - Pueblo Park
  - Arizona Park
  - APEX motor club

2024-02-27 Client: 101.0-exp Firmware: 101.0-exp

Firmware:

New features:
- Support for the new “5x3MT Ecumaster with 2 encoders” keyboard
Fixes:
- Min/Max channel values are working correctly (fixed issue introduced in version 100.0-exp)

Client:

Fixes:
- Fixed inconsistent number handling for keyboard layouts requiring shift to input numbers (e.g. Czech or French)
- Resolved issue causing application to become stuck in full-screen mode

2024-01-19 Client: 100.0-exp Firmware: 100.0-exp

Firmware:

New features:
- Support for PMU-24 CAN stream (new dedicated pmuX.* channels)
- Support for Autosaved Channels
- Timers: Start Behaviour parameter added
- Park letter “P” added to the Gear Indicator control (it uses -2)
Improvements:
- GPS can be located at ID=0x646 (the ID does not need to be a multiple of 0x8)
Fixes:
- Changing CAN2 speed now properly reinitializes custom Project Tree CANbus Message Objects

Client:

New features:
- File / Merge Project… (Ctrl+M) command added
Improvements:
- Application is now properly scaled on high DPI monitors
- The saving and loading of Analog Input and User Table dialogs is now functioning correctly.
- Axis channel for a table can now be changed without regenerating axis bins (use context menu: Modify Axes / X/Y Axis Properties… and set Generation Type to Change Channel Only)

CAN Streams:

New:
- PMU-24_#1_ID668.canx
- PMU-24_#2_ID678.canx
- PMU-24_#3_ID688.canx
- TPMS_WHP.canx
Renamed:
- PMU1.canx renamed to PMU-16_#1_ID668.canx
- PMU2.canx renamed to PMU-16_#2_ID670.canx
- PMU3.canx renamed to PMU-16_#3_ID678.canx

2023-08-25 Client: 94.0-exp Firmware: 94.0-exp

Firmware:

New features:
- – Hillclimb lap timing mode added.
- – Shift Light: Pit Limiter Indicator added (white and blue LEDs can alternate when a PIT limiter is active)
- – Timers: Reset functionality added.
- – New channel ‘adu.track.isBestTimeSet’ added
Improvements:
- – Permanent variables (such as an odometer) are now immune to disconnecting the battery during a write operation.
- – Decreased the blue component contribution in the final LED color for user lights. Now the violet, cyan, and white colors are more distinguishable.
Fixes:
- – An alarm ‘.active’ channel: the “Delay time” is properly handled.

Client:

New features:
- – Hillclimb mode added to Track visualization.

2023-08-22 Client: 92.2.1 Firmware: 92.2

Notes:

– The firmware 92.2-beta is now renamed to 92.2. It’s exactly the same firmware.

Client:

Fixes:
- – Fixed a bug that prevented the firmware from being upgraded on the first attempt.
- – Fixed a bug with real-time logging that sometimes didn’t start after a firmware upgrade.

2023-06-15 Client: 92.2-beta Firmware: 92.2-beta

Firmware:

New features:
- – ECUMASTER CANbus Keyboards:
- – Support for ECUMASTER 5×3 RGB keyboard
- – New channel ‘kb_X.active’ was added to CANbus Keyboards. It’s ‘1’ when a keyboard is connected to a device.
Fixes:
- – RPM Bar:
- – The bar for Round/Bar type now displays correctly, regardless of whether the Max RPM is a multiple of 1000 or not.
- – CANbus keyboards:
- – General:
- – ‘Export keyboard buttons to CAN’ is now correctly broadcast state ‘4’.
- – ECUMASTER CANbus keyboards:
- – LED lights are now working correctly, even with the keyboard firmware v2.23.
- – The correct color is now selected when ‘First State’ is set to ‘1’
- – Grayhill CANbus keyboards:
- – Fixed an inconsistent LEDs behavior:
- – ‘Radiobutton’ button type when ‘Last state’ was set to ‘2’ or more.
- – ‘Latching switch’ button type when ‘Last state’ was set to ‘4’.

Client:

New features:
- – An option ‘Save a copy’ of an image has been added after right-clicking on the user’s icon/texture in the Texture Selector window.
Fixes:
- – The application now longer crashes when ‘Max RPM’ is set to ‘0’ for RPM Bar of type Round

2023-04-25 Client: 91.0-exp Firmware: 91.0-exp

Firmware:

New features:
- Second distance meter (adu.distanceMeter2)
- Passive OBD2 (ADU can now listen to ODB2 frames, but does not send queries)
- Prefix for log file names recorded to USB Flash drive
Fixes:
- The board revision reported by the firmware is now consistent with the one reported by the bootloader for the Light Client.
- The shutdown procedure has been improved, ensuring that the dashboard consistently turns off as intended.

Client:

Improvements:
- Performance improvements of the CSV export
Fixes:
- Application now properly checks the Table Memory limit when duplicating a Table
- Fixed the issue with the preview of the CSV not generating properly
- Fixed the issue with the CSV export crashing in case of large files

2022-09-15 Client: 90.0-exp Firmware: 90.0-exp

Firmware:

Improvements:
- ecu.user5 to ecu.eser8 channels added
- Motec M4/M45 Data Set 5 channel Drive speed assigned to ecu.user5
- Motec M4/M45 Data Set 5 channel Auxiliary temperature assigned to ecu.user6
- Motec M4/M45 Data Set 5 channel Auxiliary voltage assigned to ecu.user7

2022-09-09 Client: 89.0-exp Firmware: 89.0-exp

Firmware:

New features:
- Added support for Motec M4/M48 Data Set 5 19200 Serial Protocol

2022-09-07 Client: 87.0.1 / Firmware: 87.0

Notes:

The firmware 87.0-exp is now renamed to 87.0. It’s exactly the same firmware.

Client:

Improvements:
- Keyboard focus when editing a cell of a Table has been improved.
- USBtoCAN.DLL updated to version 15.3 with stability improvements

Fixes:

Random program crash when editing a Table has been corrected.

2022-08-02 Client: 87.0 exp / Firmware: 87.0 exp

Firmware:

New features:
- Gear Indicator control: ‘Visibility channel’ added
Improvements:
- Better accuracy of Analog Output
- Distance Meter is now immediately synchronized to permanent memory after using the ‘Reset Distance Meter’ button.

Client:

Fixes:
- Axes of tables are no longer corrupted when deleting/moving some other channels of the same type
- Proper handling of deletion/movement of a bitfield enumeration channel
- no more project corruptions.

CAN Streams:

New:

Microtech.canx
Haltech_TMS.canx

Modified:

Megasquirt2&3.canx – channels ‘canout1’ .. ‘canout8’ added

2022-02-21 Client: 86.1 / Firmware: 86.1

Firmware:

Hardware compatibility:
- Added support for second-generation display panels used by ADU7” Autosport (for devices with serial numbers 2169-xxxx or later)

2021-12-29 / Client: 86.0 exp / Firmware: 86.0 exp

Note:

Starting from 1st January 2022 all devices produced by ECUMASTER will have 12-digit serial numbers (until now 8-digit serial numbers have been used).

Firmware:

New features:
- Added support for devices with 12-digit serial numbers
- Added support for retrieving device board revision

Client:

New features:
- Added support for devices with 12-digit serial numbers
- Added board revision on Help / About screen

2021-09-29 / Client: 85.1.2 / Firmware: 85.1

Client:

Improvements:
- – DBC Importer (v4-adu):
- – An additional space before the ‘@’ character in the .DBC file is now handled correctly
- – The popup “Unit mapping file has been changed. Do you want to save it?” no longer
  appears if the unit mapping is not changed.
Fixes:
- – A division by zero crash has been fixed (this bug could occur when the divider of CANbusInput
  has been set to zero by a previous version of DBC Importer).

2021-09-24 / Client: 85.1.1 / Firmware: 85.1

Firmware:

Improvements:
- – Added support for the 10Hz GPS mode of the Ecumaster GPS. (Ecumaster GPS uses this
  mode when the option “Enable IMU fusion” is off in the Light Client configuration. Refer to the
  Ecumaster GPS user manual for details.)

Client:

Improvements:
- – Keyboard Button Dialog: ‘First value’ / ‘Last value’ / ‘Default value’ is now disabled for buttons of
  type ‘Non- latching switch’.
Fixes:
- – Application no longer crashes when loading 1 pixel user texture.
- – Popup “Texture buffer send fail!” no longer appears when working with user textures offline.
- – Ranges of channels ‘adu.track.startLine*’ have been corrected.

2021-07-07 / Client: 85.0.2 exp / Firmware: 85.0 exp

Client:

Improvements:
- – Log files saved with Client has now proper Duration field in Download Log File dialog (Shift+F4)
Fixes:
- – Reference track generation no longer crashes when GPS IMU is disabled. The process uses
  ADU accelerometer instead

CAN Streams:

Fixed:
- – EvoX.canx – fixed c_gear channel

2021-06-07 / Client: 85.0.1 exp / Firmware: 85.0 exp

Client:

New features:
- – Graph Log: Added export to Racelogic VBOX .VBO file
- – Graph Log: Added export of screenshot to PNG file

Changes:

– Graph Log: ‘Export to CSV’ icon changed to more general ‘Export to Text File’

2021-05-21 / Client: 85.0 exp / Firmware: 85.0 exp

Firmware:

New features:
- – Detection of ADU Rev.2 hardware and reporting this information to the Client software.
Improvements:
- – Increased number of Operations to 100 (up from 80)
- – Increased number of logical Functions to 60 (up from 40)
Fixes:
- – Fixed graphical glitch on Tire/Brake Temperature Graphs in Bar mode

Client:

New features:
- – Added firmware upgrade prompt when opening the project file from newer firmware version
- – Added “Offline firmware configuration selection” when loading project files from older firmware in
  offline mode (with CAN adapter not connected to PC)
Improvements:
- – Firmware upgrade prompt when connecting to the device is displayed only once for each
- – Improved “Project conversion report” after opening the project file from a different firmware version.

Fixes:
- – GPS channels ‘gps.latitude’ and ‘gps.longitude’ have now proper ranges (fixed for firmware
  configuration 80.x and later)

2021-05-12 / Client: 84.0 exp / Firmware: 84.0 exp

Firmware:

New features:
- – Added support for Ecumaster family and Grayhill family keypads
- – Added support for Brake Temperature Cameras (btc.* channels). It works as a builtin device
  (similar to GPS and Tire Temperature Cameras) and no additional CAN Inputs/Message Object
  are required
- – Number 8 added to gear indicator big character set
- – GPS base CAN ID can be changed (the base ID must be multiple of 8)
- – Rotation of tire temperature bar graphs
Improvements:
- – Switching the ignition switch back on when Delayed Turning Off is used causes ADU to restart
  (it is possible after 0.5 seconds after starting the Delayed Turning Off procedure)
Fixes:
- – Vertical bar graph unit and value color bug fixed
- – Corrupted characters when the user track name was 16 characters long bug fixed

Client:

New features:
- – Added firmware upgrade prompt when connecting the device for the first time to client software
- – Track preview shows the starting point recorded in the log file
- – Track preview raw GPS data is now marked with colour depending on the GPS status
- – Added “Internation style CSV export” (uses ‘.’ and ‘,’ characters)
- – Added fixed frequency option for ADU CSV export
Fixes:
- – Track preview doesn’t show GPS points gathered before stable signal was recorded
- – Hit test for tire temperature scale fixed
- – References to some Enumerations was accidentally deleted when deleting an Enumeration

2021-03-29 / Client: 82.0.2 exp / Firmware: 82.0 exp

Client:

Fixes:
- – The Client software no longer crashes when trying to generate Reference Track from a very
  small set of GPS points
- – The Client software no longer crashes when trying to compare laps with the Reference Track
  generated

2021-01-13 / Client: 82.0 exp / Firmware: 82.0 exp

Firmware:

New features:
- – Delayed turning off (requires separate Battery 12V and Ignition Switch 12V wiring)
- – Use the Configuration panel of the CONFIGURATION tab to setup. The following options
  can be specified:
  - – Turn Off Minimal Time [seconds]
  - – Turn Off Maximum Time [seconds]
  - – Turn Off Channel (when this channel becomes high (non-zero) after Minimal Time the
    device will power off).
- – Channel ‘adu.isTurningOff’ has been added to do custom actions
- – CANbus Export: DLC can be specified
- – PULS oil level and temperature sensor support – can be wired to Digian Input D4 (‘adu.puls.*’
  channels have been added)
Serial protocols:
- – New serial protocol: Ecumaster Classic EDL protocol
- – New serial protocol: Athena GET protocol
Improvements:
- – USB logger: log files are now safely closed when ADU device is turned off by Ignition Switch low
  (requires separate Battery 12V and Ignition Switch 12V wiring)
- – Fuel Level Filter: when using “Two fuel sensors (average)” mode the channel ‘ecu.fuelLevel2’ is
  now set to 0.0.
- – ODB2 Refresh Rate can now be specified as low as 1Hz

Client:

New features:
- – Histogram view added
- – Lap Time Plot view (Lap time vs Lap number) added
- – Section Times view has now View Sectors mode
- – Finish/Start line is shown on the Track Preview window
Improvements:
- – Section Times view: display performance has been improved
Fixes:
- – The Client software no longer crashes when accessing a single bit of a channel created by
  Enumeration of type Bitfield

2020-10-14 / Client: 81.8 / Firmware: 81.8

Notes:

– Official version

2020-09-21 / Client: 81.8 exp / Firmware: 81.8 exp

Firmware:

Fixes:
- – USB logger: occasional data corruption has been fixed
- – USB logger: fixed bug when the logger sometimes incorrectly created a series of small files
  (1kB)

Client:

Improvements:
- – The client software is now able to load log files with occasional data corruption.
Fixes:
- – Graph Log properly resume recording of the log data after the firmware upgrade even a log file
  was loaded right before this firmware upgrade
- – Graph Log: maximum value of PMU outputs voltages increased to 16V

2020-08-13 / Client: 81.0.1 exp / Firmware: 81.0 exp

Client:

Fixes:
- – Editing tables (e.g. Calibrated Analog Sensors): pressing Tab or clicking outside the control now
  accepts the entered value

2020-08-11 / Client: 81.0 exp / Firmware: 81.0 exp

Firmware:

New features:
- – New operation for Numbers – Get Temperature Element – to access individual TireTempCam
  samples
- – Possible to read normal and compound inputs from one CAN frame
- – Toggle operation has now two new optional channels:
- – “Set channel” to set value to 1
- – “Reset channel” to reset value to 0
Fixes:
- – Digital inputs are no longer incorrectly activated at startup. (Resolved bug with starting at the
  second page).

2020-04-09 / Client: 80.0 exp / Firmware: 80.0 exp

Firmware:

New features:
- – More CANbus Message Objects – 50 shared by CAN1 and CAN2 (up from 8+8)
- – Support for CAN Inputs located across 3 bytes (e.g. endian=little, bitCount=13, bitPosition=13)
- – Custom multiplexer for compound CAN frames – any bitPosition and bitCount up to 16 bits
- – Button Defined Track (tab CONFIGURATION / pane Buttons / Button defined track start line set)
- – press the button at the new start/finish line and then do the one lap to define the custom track
Improvements:
- – CAN frame with wrong DLC (e.g. 15) is now treated as DLC=8 (solution for GET_H4FSAE ecu)
- – Serial stream can work in parallel with CAN stream. No need to remove the EMU BLACK stream
  if you use data from serial connection.
Changes:
- – CANbus Message Objects timeout works for all frames at once, not for individual frames like before

Client:

New features:
- – DBC Importer: support for compound streams (firmware version 80.0 is recommended)
Improvements:
- – DBC Importer: signal multiplier and divider calculation has been improved
Fixes:
- – Proper CAN ID displayed on CANbus Message Object Dialog when PMU1/2/3 is selected
- – Import CANX dialog: red background of ID control no longer appears when importing
  Holley_HEFI.canx
- – Fixed the bug that sometimes stopped a firmware upgrade process in the bootloader phase.
Changes:
- – Project files created with this ADU client version cannot be loaded to an older version of the
  software. Please backup your projects before installing.
  Default project pg_page1.adu:
  Added:
- – overlay page ov_buttonDefinedTrack added (requires firmware 80.0 or later )
  Analog switches to ground have been added to control ADU functionality:
  - – A3 – fuel level sensor
  - – A4 – zero IMU pitch
  - – A5 – acquire Button Defined Track
  - – A6 – acknowledge alarm
  - – A7 – previous page
  - – A8 – next page
- Ecumaster USBtoCAN:
  - – Internal software updated to v15.1 (automatic update offered when starting the ADU Client)

CAN Streams:

New:
- – BoschMotorsport_MS4Sport.canx

2020-01-29 / Client: 65.0.2 / Firmware: 65.0

Client:

Fixes:
- – The Client software works again on Windows XP (fixed regression from version 65.0)

2020-01-20 / Client: 65.0.1 RC1 / Firmware: 65.0

Notes:

– The firmware 65.0 and 65.0-beta are exactly the same firmware.

Client:

Fixes:
- – Proper CAN ID displayed on CANbus Message Object Dialog when PMU1/2/3 is selected
- – DBC Importer: Proper importing of big-endian signals when bitPosition/bitCount is not multiple of
  8 bits.
- – Fixed device crashes after firmware upgrade when too many logged channels were used.
- – The name of an icon for gauges/bar-graphs is now properly loaded from the .ADU file.

CAN Streams:

Updated:
- – Motec_M1.canx: channels c_Driver_Switch1..6 and c_Driver_Rotary_Switch1..8 added
- – VAG_MED91.canx: channel ecu.usedFuel added

2019-12-19 / Client: 65.0 beta / Firmware: 65.0 beta

Firmware:

New features:
- – Zeroing of IMU pitch added – panel ‘Buttons’ / ‘IMU pitch zeroing…’
- – Virtual fuel tank
- – Fuel level filter can be disabled (default) when there is no RPM (useful in tank zone)
- – Visibility channel added to Lines, Rectangles, and Circles.
- – Channel ‘adu.anyAlarmActive’ added
Improvements:
- – Increased CANbus Export bandwidth to 500 Hz on CAN1 + 500 Hz on CAN2 (up from 500 Hz
  total for both CAN1 and CAN2)
Fixes:
- – Shift Light: Table3D mode – ‘Flash when all LEDs on’ with ‘Flash colour’ = ‘Use default colors’ is
  now working as expected

Client:

Improvements:
- – CANbus ID=0x000 is now allowed for CANbus Message Object and CANbus Export
  – DBC Importer: improved signal importing for factors 0.2, 0.5 and similar.
- – Alarm dialog: proper handling of decimal places in qualifier condition
Fixes:
- – Expanding/collapsing the CANbus Message Object in ProjectTree no longer resets every CAN
  Input in the device
- – Log channel frequency is always written to the .ADU document file.
- – Pressure Wizard in Analog Input dialog has been fixed (regression in version 63.0)

CAN Streams:

New:
- – Electronics_Limited_ME1_2.canx
- – M11_Korvet.canx
- – VAG_MED91.canx
- – GET_H4FSAE.canx
Updated:
- – Motec M1: CAN Input c_Fuel_Used_M1 changed to ecu.usedFuel
- – Pectel SQ 6: CAN Input c_Fuel_Used_ecu changed to ecu.usedFuel
- – EMU Black: CAN Input ecu.usedFuel added

2019-10-14 / Client: 63.0 beta / Firmware: 63.0 beta

Firmware:

New features:
- – New Session Results control
- – Pages can be changed directly from CAN Input or rotary switch (Configuration / Changing
  Pages)
- – Predictive time graph: Time Range parameter added
Improvements:
- – Performance optimizations
- – 15 alarms (up from 10)
Fixes:
- – Alarms: alarms are now disappearing properly even the Retrigger Time or Min Show Time
  parameters are greater than 5 seconds.

Client:

New features:
- – DBC file importer (ProjectTree / Add / Import .CANX/DBC file)
Fixes:
- – Alarms: changing the Unit parameter in the alarm dialog works as expected.
- – Alarms: previewing the alarm on PC now takes into account the Decimal Places parameter.
- – Alarms: the alarm dialog fits correctly even on small screens.

2019-08-27 / Client: 60.3.2 beta / Firmware: 60.3 beta

Client:

New features:
- Support for Peak PCAN-Ethernet Gateway.
Improvements:
- Default texture size after resizing is now 200×200
- Improved image preview when adding new texture/icon

2019-08-01 / Client: 60.3 beta / Firmware: 60.3 beta

Firmware:

Fixes:
- Improper serial number no longer causes connection problems with the Client software.

2019-07-29 / Client: 60.2 beta / Firmware: 60.2 beta

Firmware:

Improvements:
- Gauge control: Angle Span and Angle Offset parameters are now implemented
- RoundGauge control: Angle Offset parameter work correctly when the value is over 90 degrees
- CAN ID 0x7E8 can be used with CANbusMob / CANbusInput when OBD2 Enable is off

Client:

Fixes:
- Import .CANX file dialog: Show Frames checkbox now properly shows all the frames (corrected bug with multiple mobs in one file)

2019-06-07 / Client: 60.0 beta / Firmware: 60.0 beta

Firmware:

New features:
- Added BracketRacing lap timing mode (Configuration pane / Lap timing)
- Added triggered transmit mode for CANbusExport
- Added Speed Source for ecu.speed – CAN, GPS or custom channels such as Digital Inputs (Configuration pane / Speed source for ecu.speed).
- Added list of additional circuits
- Increased number of Tables to 20 (up from 10)
Improvements:
- ResetSession button is now resetting also the CurrentLapTime, LastLapTime, PredictiveLapTime, adu.track.lap, adu.track.gainLoss, adu.track.lapTime, adu.track.lapDistance
- PredictiveLapTime and adu.track.gainLoss is now calculated once crossing the start/finish line
- Visibility Channel is now working for UITime
Changes:
- The adu.track.lapTime channel can now be negative (in some cases in the Bracket Racing)

Client:

New features:
- GraphLog: Shift+S toggles between lines and points+lines
Improvements:
- Widths of columns are preserved: ProjectTree, TextLog, VariablesInspector

CAN streams:

LinkECU_GenericDash.canx – divider for oil pressure changed

Ecumaster USBtoCAN:

Internal software updated to v14.0 (automatic update offered when starting the ADU Client). This software improves compatibility with an older version of PMU/ADU Client.

2019-04-22 / Client:55.2 beta3 / Firmware: 55.2 beta3

Impovements:

Rendering the TrackRecordTable and Grid controls has been optimized.

Fixes:

Fixed bug when best time appears multiple times on the Track Record Table.
Rendering of empty group with SyncRendering=1 no longer causes corruptions.

2019-04-15 / Client:55.1.1 beta2.1 / Firmware: 55.1 beta2

Fixes:

The dimensions of the Shift light table is now always 9 LEDs x 7 gears. The project needs to be saved and opened from the disk or the firmware upgrade needs to be performed.
Using the menu command Restore to default more than 50 times no longer leads to the Client software crash.

2019-04-04 / Client:55.1 beta2 / Firmware: 55.1 beta2

New features:

New Memory Report window (Tools/Memort report…)

Improvements:

Support of Default Text and Default Color in Enumeration is finally working.
BarGraph: Edit Gradient window – “Remove gradient” button added
BarGraph: Color from Gradient is no longer multiplied by Bar Color.
BarGraph: When the alarm is active, the gradient bar is displayed using a solid color (Alarm color).
Ecumaster USBtoCAN adapter – improved firmware upgrade on Windows XP
Peak PCAN adapter – added support for Windows XP

Fixes:

First value of the Calibrated Analog Sensor after startup is consistent with later values.
Analog Inputs with decimal places can be properly sent to CAN
Duplicating element with the name containing 30 characters no longer leads to the project corruption.
Group control: proper arrangement of controls with zero width or height (such an empty Text control)
Bug with start/finish line introduced in version 55.0 beta1 fixed
Bargraph gradients: proper refresh on device after change in the Client software

2019-03-22 / Client:55.0 beta1 / Firmware: 55.0 beta1

New features:

Channel Simulator offline and online (press F9 and type “simulator”)
New page backgrounds
Ctrl+K pressed on the Preview window, saves the current page image (800×480) to a png file
ADU builtin accelerometer calibration – new channels adu.latG/adu.longG
Gradients for bargraph
Channels gps.longitude / gps.latitude can be exported to CAN (32bit values)
Switch element can now count downwards using channel “Input channel down” / “Trigger edge down”
Now the ADU is visible in the Light Client
Detection of Autosport ADU version
Active alarms are written to log. Each alarm channel has. active property
Another log can be appended after the loaded log file.
Compare laps – use the Compare laps icon on the Graphlog toolbar. Use cl.timeSlip channel to show the difference in seconds between two laps. The x-axis of the log can be selected between distance or time.

New CAN, serial streams

AEM serial stream,
GEMS serial stream,
ABIT M1 CAN stream,

Improvements:

Support for Kvaser CAN adapter was improved
New Ecumaster USB2CAN firmware (0.12)
Added SaveAs prompt when connecting the ADU with different firmware to prevent project loss in the

Client.

Larger Preview window
Widths of columns in the Project Tree are properly restored
New image blend mode (Multiply)
Bar graph:
New Bar type – Horizontal bi-directional and Vertical bi-directional
New Bar style – Simple without decoration
RPM Bar:
Nonlinear scale
Different tick configuration
Numbers describing RPMs can be centered under tick marks
RPM Bar can use texture as a gradient

Fixes:

Channels gps.longitude / gps.latitude are properly displayed by Text control.
Text cropping issues fixed in Texture Selector (high DPI).
Graphical glitches for RPM round gauge fixed
Changing the speed of the CAN2 no longer causes Bit Stuffing Errors.
Enumeration of type Bitfield used inside the Grid control: when the textual representation of such Enumeration exceeds 64 characters the ADU device no longer freezes. Firmware upgrade is recommended.

Changes:

Tire temperature cameras base adress changed to 0x420
Tire temperature cameras range increased to 255C
There are 30 icons or textures available for the user

Important:

ADU project created with this ADU client version cannot be loaded to the older version of the software

2019-04-04 / Client: 52.6 (MASTER) / Firmware: 52.6 (MASTER)

New features:

Detection of an Autosport ADU version in the Client software

Improvements:

Support of Default Text and Default Color in Enumeration is finally working.

Fixes:

Text cropping issues fixed in Texture Selector (high DPI).
Size of Texture Selector window fits properly small screens.
Size of Load Page Template window fits properly small screens.
Duplicating element with the name containing 30 characters no longer leads to the project corruption.
Changing the speed of the CAN2 no longer causes Bit Stuffing Errors.
Enumeration of type Bitfield used inside the Grid control: when the textual representation of such Enumeration exceeds 64 characters the ADU device no longer freezes. Firmware upgrade is recommended.

2019-02-11 / Client: 52.5 (MASTER) / Firmware: 52.1 (MASTER)